First off, that’s not the industry standard. At least, not for any industry I’m familiar with. ARM-based MCUs like the Freescale Kinetis series or ST. M16C. From Wikipedia, the free encyclopedia. Redirect page. Jump to navigation Jump to search. Redirect to: Renesas Electronics#M16C microcontrollers. R5FMDFA#U0 from RENESAS >> Specification: Microcontroller, M16C Family M16C 60 Series Microcontrollers, 16bit, 25 MHz, KB, 31 KB.
|Country:||Republic of Macedonia|
|Published (Last):||17 April 2014|
|PDF File Size:||2.17 Mb|
|ePub File Size:||1.64 Mb|
|Price:||Free* [*Free Regsitration Required]|
M16C – Wikipedia
If you see a nice feature on the data sheet, then it’s worth it to consider The simliest way would be to save a variable in every MCU i think. Nothing is really superior in general, it’s more so what fits your project. I personally like to add toolchain support on Linux as that is a very comfortable platform for developing your own software and tools in my opinion.
Not to forget good readable datasheets. If your application provides a UART interface on UART1 of m166c device, and if mcirocontroller application has some jumper or so to set the device microcontrollfr flash programming you don’t need additional hardware for programming M The variable should be in a non volatile part of memory.
Start with something that you can understand using your existing level of knowledge and skill. Just a few things have to be taken care of, like connecting some pins kicrocontroller the MCU properly. There are a slew of easy-to-use MCU development boards out there to remedy this. I’m thinking maybe this is a type of spam. The Renesas M16C is not an ‘industry standard’ for me.
How can I achieve that? One option is to use a 1-wire “silicon serial number” chip DS What matters is “community standard” i. Again from a availabiltity of tools, source codes and documentation point of view. So, to answer your question, I really can’t think of a reason why you should use a Renesas M16C.
FDT does not support such an old device as M Usually, you go with a component that meets the need and nothing more. Do I have to write a ID in memory first or does such a number already exist? Your micfocontroller is too vague, and opinion based for it to be microcontdoller good fit to this site. I still have some questions: What are the advantages of working with the Renesas M16C microcontroller?
I already downloaded FDT. In order to identify a device I would like to read out a uniqie ID from the mfcgp. User Join or Sign In. Meaning, we can’t say what is better for you, that depends on your project. I went to their official website and I did some quick research but I didn’t understand much.
In any case I voted microcontrolleg close as too opinion based. Thank You both for these suggestions. I know it’s the industry standard but what would it add to my simple project?
I also have some information on serially programming m32c’s here: Then ask specific questions here. The solution with external chips is to complicated i think. Please read the help center to learn how to ask good questions. First off, that’s not the industry standard. What if I use: Each is guaranteed to have a unique bit serial number, and you only need to use up one pin of the MCU to interface with it.
Schould I choose the generic boot kicrocontroller You have given no explanation for what you need it for, so we can’t offer any rational, evidence-based analysis.
Also downvoted due to very badly written. Another issue is that: For DIY projects, however, “industry standard” doesn’t matter. So we can’t help you. There are many more MCU lines mircocontroller are used quite a lot.
Another way is to have your flash programmer insert a unique serial number at a fixed location in each image it saves, but if you’re doing remote updates that might wipe out the number unless you’re careful to not reprogram that flash block. Many good questions generate some degree of opinion based on expert experience, but answers to this question will tend to be almost entirely based on opinions, rather than facts, references, or specific expertise. Would it be ok to work with an Arduino for instance?
If midrocontroller can’t understand it from the website and its datasheet, then it’s unlikely that you are going to be successful using it. To read a string of bytes from a pre-determined memory address FFFC0 in this exampleuse code like this:.